UK

CONSTRUCTION
The pullover is worked from the top to the
bottom. Begin by casting on neckline stitches and join to work in the round. At the same time, the four raglan “seams” are marked for the location where increases will be worked. Increases are worked on each side of the set of 5 raglan stitches at 4 locations around the yoke until the yoke is the desired length. From the RS facing, the 5 raglan stitches are: one knit, three purls, one knit. Then, the sleeve stitches on each side are placed on waste yarn and stitches at the underarm of each sleeve are cast on. Now, continue to work the body in the round to the desired length. The bottom band is worked in a ribbed pattern and then all stitches are bound off. Transfer the sleeve stitches to a short circular needle and pick up stitches along the underarm edge. The sleeve is shaped with decreases until the sleeve is the desired length. Then, a ribbed cuff is worked to the desired length, and the stitches are bound off. Finally, the collar along the neckline is worked in ribbing to the desired height and then all stitches are bound off.

SIZES
1 (2, 3, 4, 5)

MATERIALS
The quantities identified below may vary depending on the desired width and length. Therefore, the quantities should be considered as a starting point and then adjusted for desired lengths and widths.

200 (200, 250, 250, 300) g Isager Uld 2
100 (100, 125, 125, 150) g Isager Silk Mohair
20 g Isager Spinni for the thin stripes either in one color or in different colors of Isager Spinni

This pullover will be worked using two strands of yarn held together throughout the entire work: one strand of Isager Uld 2 and one strand of Isager Silk Mohair. Then, in every 8th round, one strand of Isager Spinni will be added to the other two strands for the stripes. Thus, three strands of yarn will be held together.

Alternate yarn suggestion:
150 (150, 175, 175, 200) g Isager Soft Fine
150 (150, 200, 200, 200) g Isager Spinni
20 g Isager Spinni for the thin stripes either in one color or in different colors of Isager Spinni

MEASUREMENTS
It is recommended to measure an existing and well-fitting sweater that matches this design shape and yarn quality before starting to knit. Individually determined dimensions should then be matched to one of the following sizes:

Chest Circumference: 116 (122, 132, 140, 150) cm or
46 (48, 52, 55, 59) inches
Length: 50 – 65 cm or 20 – 26 inches or desired length. The design is worked from top to bottom.
Sleeve Length: 35 – 45 cm or 14 – 18 inches or desired length. The sleeve is worked from top to bottom.

GAUGE
16 stitches = 4 inches
28 rows = 4 inches

RECOMMENDED NEEDLE SIZE
5 mm (US 8) double-pointed or circular in lengths of 40, 60 and 80 cm (16, 24 and 32 inches)
Use a 4.5 mm (US 7) needle for the edge bands. Or, if a tighter band is desired, use a 4 mm (US 6) needle.

//

DK

KONSTRUKTION
Sweateren strikkes oppefra og ned. Begynd med at slå nakkens m op, og tag ud i hver side til halskant. Samtidig markeres raglan og raglanudtagninger. Når alle m er med i halsudskæringen, samles arbejdet, og der fortsættes rundt på rundpind, idet der på hver 2. omg laves udtagning på hver side af de 4 x 5 raglanm, indtil raglan har den ønskede længde. Sæt ærmemaskerne i hver side på snor, og slå masker op til ærmegab under hvert ærme. Fortsæt rundt med kroppens m til den ønskede længde. Strik ribkant, og luk af. Sæt ærmemaskerne på rundpind. Strik m op langs ærmegabet, og fortsæt rundt med udtagninger på rundpind, til ærmerne har den ønskede længde. Strik ribkant, og luk af. Til sidst strikkes halskanten også i rib til den ønskede højde. Luk af.

STØRRELSER
1 (2) 3 (4) 5

MATERIALER
200 (200) 250 (250) 300 g Isager Uld 2 fv E0
100 (100) 125 (125) 150 g Isager Silk Mohair fv E0
20 g Isager Spinni til den tynde stribe, som enten kan være i samme farve eller dine forskellige Spinnirester.

Der strikkes med 2 tråde gennem hele arbejdet, en tråd Isager Uld 2 og en tråd Isager Silk Mohair.
På hver 9. omg også med en tråd Isager Spinni = 3 tråde i alt.

Garnalternativ
150 (150) 175 (175) 200 g Isager Soft Fine
150 (150) 200 (200) 200 g Isager Spinni
20 g Isager Spinni til den tynde stribe, som enten kan være i samme farve eller dine forskellige Spinnirester.

MÅL
Halv brystvidde: 58 (61) 66 (70) 75 cm
Hel længde: 50 – 65 cm eller den ønskede længde, da modellen strikkes oppefra og ned.
Indre ærmelængde: 35 – 45 cm eller den ønskede længde, da ærmerne strikkes indefra og ud.

Garnmængden kan variere en del efter den bredde og længde, der ønskes. Derfor er garnmængderne vejledende.

STRIKKEFASTHED
10 cm = 16 m
10 cm = 28 p

VEJLEDENDE PINDE
Nr. 5 – Strømpepinde og rundpinde 40, 60 og 80 cm
Kanter evt. på et halvt nummer tyndere pinde